The Team

Adam Rana, Project Manager

Jungkyoo Park, Stress Analyst

Ilute Nyambe, Finance Officer
Ravi Parmar, Material Specialist
Arnold Ngang, Chief Designer

Wednesday, 21 April 2010

General Comparison of Aluminium and Steel

We have come to the conclusion as a group that our crane will either have to be made up of Aluminium or Steel whilst taking into account their respective weight, cost, and durability in the long run.

Similarities

To start with the similarities of aluminium and steel:

- Structural applications of aluminium and steel are mostly similar;

- Design problems/processes are similar so an identical approach is used;

- The design rules for aluminium and steel (EC9 and EC3) are purposely very similar, see the first two reasons.


Differences

However, there are important differences in physical as well as mechanical properties which have to be accounted for in the design process. The table on this page gives a comparison between the most important physical properties of aluminium and steel. The differences in properties, the consequences for structural behaviour and how to deal with that in structural design will be elucidated below.

First of all, the low density of aluminium is the main driver for using it in many structural applications. The high strength to weight ratio is the number one reason for the development of the aircraft industry. Although its low weight is a favourable property, it can in some cases be a disadvantage; for example with cyclic loading the ratio live load/dead load is disadvantageous as compared to steel and so fatigue must be considered early in the design stage.


The low density makes an aluminium structure prone to vibrations and in these cases the dynamic behaviour of the structure has to be considered. The Young modulus, E is important for the structural behaviour. Its value is about 1/3 that of steel, but contrary to density, this is a disadvantage compared to steel.

The low value of the Young modulus, E has a big influence on the deformations of an aluminium structure. A well-known example is the bending of beams, where the stiffness EI is the governing factor and IAl = 3 ISteel to arrive at the same stiffness as a steel beam which is illustrated in the table below.

The above indicates that in designing aluminium structures, it is often not the strength, but in many cases the deformation, that is the governing factor. So in building and civil engineering it is frequently the alloy which does not have the highest strength that has to be considered.

The low Young modulus is also responsible for the higher sensitivity to stability problems in aluminium structures (buckling). The critical stress for buckling is linearly related to the Young modulus. Moreover, aluminium designs often have very slender, thin walled sections which make it even more important to consider their stability in designing structures.

Finally, there is cyclic loading, where the Young modulus is responsible for the lower fatigue strength of aluminium – circa half that of steel. This, in combination with the low density, means that fatigue design should be considered more carefully than with steel structures. Similar to the Young modulus is the shear modulus G which is also about 1/3 of that for steel. This means that the resistance against shear forces, shear deformations and shear stability (for example lateral torsional buckling of beams) can be an important aspect in the design.

Tuesday, 20 April 2010

Design assembly ( preliminary stage)



This is the first stage of the assembly of the our final design. The beams are mounted onto the rotating base. This base will contain ball bearings which whill allow the posibility for easy rotation when needed.

Outtriggers for Support



These are the structures that offer support to the crane structure on rough ground.
the holes help in changing levels to match an appropriate height.

Monday, 19 April 2010

The winch system to implement.

For the project we will be using two winches to operate the crane. The purpose of the first will be to lift the object to be moved from the ground to a suitable height above the ground. The second winch will be aimed at lifting the top H-beam to provide more height during lifting to avoid any obstacles.

Research into the different types of winches was made and it was noted thst there were three main parts to a winch. They are the spool and other parts related to holding the rope, strap or cable; the crank, power source, and gears; and the ratchet. These parts can be mixed relatively independently though some combinations are better than others.

So after careful analysis we decided use the Fulton 3,200lb Two Speed Cable Winch w/ Hand Brake - HP Series. This winch would be used for lifting the H-beam. its features include:

Product Length: 12.0 inches
Product Width: 9.0 inches
Product Height: 8.0 inches
Product Weight: 18.3 pounds
Package Length: 12.0 inches
Package Width: 9.0 inches
Package Height: 8.0 inches
Package Weight: 17.3 pounds

Description
3,200 lbs. Single Speed Capacity: 3,200 lbs. Gear Ratio: 5.1:1 and 12.2:1 Handle Length: 10






The second winch which we found was the T12 hand winch/manual winch. This is a winch which was designed to be used with cranes. product descriptions include:

Aplication: Cranes
Capacity: 1200kg
Power Source: Hand
Surface: Zinc